Shaking Table
Shaking table enjoys the advantages of high enrichment ratio and good separation efficiency.If you have are interested in it,click for full detail
[email protected]
Shaking table enjoys the advantages of high enrichment ratio and good separation efficiency.If you have are interested in it,click for full detail
[email protected]shaking table is one of the main equipment of gravity concentration. It widely applies in the classification of tungsten, tin, tantalum, niobium and other rare metals and precious metals ore and can also be used for classification iron, manganese ore and coal. When dealing with tungsten, tin ore, the table effective recycling granularity scope is 2-0.02 mm. 6-S table enjoy the advantages of high rich ore ratio, high classification efficiency, safeguards easily and easy to adjust stroke.
Beneficiation process is in an inclined bed to strip on the surface, the particle swarm was fed into the shaking table from the feeding chut on the corner of the bed. At the same time, the sink will supply the landscape washing water. So the ore pellets layer on the basis of particle size and proportion under the influence of gravity, Horizontal water impact,the reciprocity and friction of the bed are done by reciprocating asymmetric motion. The ore pellets with different particle size and the proportion was running along with their direction of travel from A side to B side fan-shaped shed, and then it will be pulled out from different area of concentrate and tailings discharge end side, finally is divided to concentrate, middlings and tailings.
| Name | Grit concentrator table |
Fine sand concentrator table |
Sludge concentrator table |
|
| Bed surface Dimensions |
Length (mm) |
4450 | 4450 | 4450 |
| Driving part Width (mm) |
1855 | 1855 | 1855 | |
| Concentrate part Width (mm) |
1546 | 1546 | 1546 | |
| Max.feeding size(mm) |
2 | 0.5 | 0.15 | |
| Feeding amount (t/d) |
30-60 | 10-20 | 15-25 | |
| Feeding thickness (%) |
25-30 | 20-25 | 15-25 | |
| Stroke (mm) |
16-22 | 11-16 | 8-16 | |
| Frequency (f) |
45-48 | 48-53 | 50-57 | |
| Bed surface Water quantity (t/d) |
80-150 | 30-60 | 10-17 | |
| Bed surface Horizontal obliquity(°) |
2.5-4.5 | 1.5-3.5 | 1-2 | |
| Bed surface Portrait obliquity(%) |
1.4 | 0.92 | ---- | |
| Table board corner(°) |
32-42 | 40 | 42 | |
| Concentrating area(㎡) |
7.6 | 7.6 | 7.6 | |
| Bed surface Length ratio |
2.6 | 2.6 | 2.6 | |
| Shape of side-bed surface |
Rectangle | Zigzag | Triangle | |
| Motor power(kw) |
1.1 | 1.1 | 1.1 | |
| Transmission device |
Eccentricity | |||
Cone crusher is an important equipment for the stone pit. According to incomplete statistics, the mechanical failure of the cone crusher due to improper lubrication is as high as 30% of all faults.
We need to purchase a small crusher for crushing glass. The capacity is 500 kg per day. Can your company supply for us?
Contrastive analysis of cone crushers and jaw crushers.1.Category description of cone crushers and jaw crushers.2.Structural description of cone crushers and jaw crushers.3. Operating principle of cone crushers and jaw crushers.4.Applicable materials of cone crushers and jaw crushers. 5.Crushing capacity of cone crushers and jaw crushers.
Why is the jaw crusher favored by massive users? Firstly, the jaw crusher can complete the crushing process independently.Secondly, the jaw crusher is all-match, not just talking, it can be seen in every production line in the mine production.
FTM jaw crusher liner is composed of the liner body, the hollow lightening hole in backside, anti-loose fixture block hole, reinforcing rib, anti-loose fixed block, lifting hole, etc. Each parts strengths of FTM jaw crusher liner will be presented below.